論文

Automation of loading explosives in mountain tunnel excavation is being promoted to solve the shortage of skilled technicians and the high incidence of industrial accidents. Loading explosives requires human-specific skills such as appropriate force, sensation, and adaptation to environmental changes, which have not been considered in previous studies. In this study, force-aware automation was realized that can adapt to environmental changes based on motion reproduction. Motion reproduction uses bilateral control to record and reproduce movements, and has the advantage of reproducing forces and teaching human skills to manipulators. Meanwhile, if the 3D relative position of a loading hole and a 6-DOF manipulator or the orientation or the unevenness of the loading hole changes from the recording mode, the recorded task will not be successful. Therefore, a method is proposed herein for detecting the 3D relative position, orientation, and unevenness of a loading hole, besides a method of motion reproduction with compensation for these changes to realize an automatic explosives loading system. The orientation is detected from the area of the ellipse extracted via image processing. Experiments confirmed that changes from the recording mode could be compensated for during reproducing so that recorded insertion motion could be successfully reproduced, even if the position and orientation changed.

Solid-state propulsion is a near-silent plasma thruster that can be mounted on drones. It generates thrust by inducing corona discharge between asymmetric electrodes, which ionizes the surrounding air and accelerates it as a plasma jet. For rapid societal implementation, numerical analysis is crucial and numerous studies have addressed this aspect. However, high-thrust solid-state propulsion systems, such as MSD (multistage ducted thrusters), exhibit complex plasma flows in which both positive and negative corona discharges occur simultaneously. Therefore, MSD analysis requires the adoption of a plasma three-component model that simultaneously accounts for electrons, positive ions, and negative ions. However, because this model involves phenomena with disparate time and spatial scales, it requires substantial computational costs. In this study, different from previous research, we attempt to reduce computational cost and enhance numerical stability by first transforming the partial differential equations representing the three-component model into ordinary differential equations using the method of characteristics and then expressing those in integral form through manual calculation. The derived integral solution was validated by comparing it with experimental results from negative corona discharge within a coaxial cylinder electrode and point-to-plate electrodes and negative corona discharge around a single-stage thruster, confirming that the simulation's predictive accuracy is reliable.

© 2020 The Authors. The International Journal of Medical Robotics and Computer Assisted Surgery published by John Wiley & Sons Ltd. Background: Microsurgery requires high skills for suturing using fragile threads, often within narrow surgical fields. Precise tension is required for good healing and to avoid the risk of thread breakage. Methods: To meet the demands, we developed a novel assist robot utilizing high-precision sensorless haptic technology. The robot adopts a cable-driven mechanism to maintain a distance from the surgical area and enhances compatibility with surgical equipment such as microscopes. The robot performance was verified through in vitro and in vivo experiments using a rat model. Results: The realization of precise tension control was confirmed in both experiments. In particular, in the in vivo experiments, the developed robot succeeded to produce a knot with an accurate tension of 0.66% error. Conclusions: The developed robot can realize to control traction force precisely. This technology might open up the window for a full assist robot for microsurgery with haptic feeling.

© 2018 IEEE. There are many falling accidents of elderly people. The main reason of these accidents is that their muscle of lower limb weaken with aging. The purpose of this research is to provide them an assisting robot that can support their weight. As the robot consists of belt and rotational motor, adjusting to subject and subject's posture is easy. Thanks to the structure, hip and knee joints' extensor torques are generated by the belt pulling up when the motor rotates. We also created an evaluation apparatus that simulates human lower limb with pulleys and links to conduct an experiment. In this paper, we consider when to assist during stance phase of walking, and the experiment was conducted in order to confirm whether the apparatus follows the motion equations. Experimental results show that there are some error between calculated force and measured force. This error may be resulted from friction between belt and pulleys.

© 2020 IEEE. With the recent development of electric drive technology, systems with multiple electric motors are increasingly used in various applications. Among them, methods of driving multiple electric motors by using only one power source is studied. This multi-motor drive system contributes to the reduction of the number of power supplies and electric parts. Because of these characteristics, the system is effective in reducing the weight and the size of whole system. Therefore, this paper proposes a circuit that can control motors by frequency separation using the principle of amplitude modulation. As a result, it is possible to drive a plurality of motors independently and simultaneously with only one power supply. The simulations of multiple motor drives by the proposed circuit was conducted.

© 2018 IEEE. In motor drive application, a high switching frequency is required in order to mitigate current harmonics which cause a copper loss. However, the high switching frequency makes the switching loss large. Hence, some switching loss reduction techniques have been studied before. However, they requires complicated circuits. This paper proposes a multilevel inverter topology for a switching loss reduction. By changing current paths, the proposed inverter realizes the zero current switching. It was experimentally verified that the proposed inverter realizes the zero current switching by a foundation circuit.

© 2019 IEEE. In this paper, Disturbance OBserver (DOB) and Reaction Torque OBserver (RTOB) considering reluctance torque is proposed. By changing the structure of DOB when performing Maximum Torque Per Amplitude Control (MTPAC), a high torque and a robust control system is designed. Specifically, a control system resistant to noise is designed by considering the reluctance torque in the torque constant part. The proposed method is effective in situations where noise is large, as in position sensorless control. Due to the noise resistance, the vibration of the current or torque is reduced. Also, by considering the reluctance torque, the estimated value of the reaction torque can be estimated accurately. Therefore the performance of the force control is improved. The effectiveness of the proposed method is confirmed by simulation.

© 2020 IEEE. This paper proposes a novel online motion modification method in motion reproduction system. Motion reproduction is used to reproduce human motion saved through bilateral control. Bilateral control is a teleoperation which can transmit both position and force. Human judgement is needed for compensating the saved motion when the environment is different. However, conventional motion reproduction system only relies on saved motion or environment in slave side. Therefore operators in master side cannot modify the motion after motion has been saved. Instead of just reproducing the motion data, the proposed method adds master system at motion reproduction phase so that an operator can modify the motion. If the master system is simply added to motion reproduction system, the operator's motion and saved motion will interfere each other. Therefore, we propose to use weightings to suppress the interference. Simulated results validates the effectiveness of the proposal.

© 2018 IEEE. Motion transmission is a technology which is expected to be used for teleoperation systems. Sensorless control can improve fault tolerance of teleoperation robots exposed to harsh environments. However, sensorless control methods are generally sensitive to parameter errors of an actuator. A previously proposed sensorless motion transmission method especially requires the accurate value of resistance. Therefore, this work aims to identify resistance of two direct current motors used as a master slave system. Taking account of the master slave system of which common mode and differential mode correspond respectively to torque transmission and velocity synchronization, a least mean squares method jointly using a voltage injection is newly applied to the differential mode. Simulation results validated the proposed identification method and indicated that the sensorless motion transmission succeeded using the identified resistance value. The proposed novel method will improve the usefulness of sensorless motion transmission by adaptability to parameter errors.

© 2019 IEEE. Recently, network-based control systems attract a lot of attentions. One of the applications of such control systems is haptic transmission using a bilateral control system. In order to construct the bilateral control system over the time delayed-network, many researchers have proposed many methods and succeeded to improve the stability and performance of the system. By assuring the system's passivity, some of conventional methods have succeeded to stabilize the system even when the communication blackout occurs. However, the passivity-based methods are conservative and deteriorate the performance. In this paper, the mode shifting method is proposed to deal with the communication blackout without considering the system's passivity. In the proposed method, the bilateral controller is shifted to a local controller when the communication blackout occurs. By shifting to the local controller, the system is not destabilized by the blackout. Moreover, when the communication recovers, the bilateral controller is gradually restored to regulate the robot's output power. Owing to the power regulation, the robots never damage environmental objects during and after the communication blackout. Therefore, the proposed method realizes stable and safe control even under the blackout. The validity of the proposed method is confirmed by simulations and a experiment.

© 2018 IEEE. Recently, Wireless Power Transfer (WPT) via Magnetic Resonant Coupling is especially focused around the world. Since a space will have a lot of devices in the future, WPT considering multiple devices will be required. It is important to consider not only power transfer efficiency but also power distribution when power is wirelessly transferred to multiple devices. The amount of received power in a receiver depends on the impedance of the receiver and the ratio of power distribution has the relation to the impedance. Conventional WPT system requires a few controllable repeaters and the large size of the receiver. In this paper, a variable impedance circuit for power distribution is proposed. Using the proposed circuit controllable by DC voltage, the problem for the conventional system is solved. In the future when WPT is popular, the circuit realizes electrically controllable power distribution.

© 2019 IEEE. Sensorless bilateral control has been studied to improve fault-tolerance of teleoperation without using torque sensors, position sensors, and other mechanical sensors. However, sensorless control often has less control accuracy due to model errors, parameter variations, and other unexpected factors. Feedback control with some position sensors is practically required for teleoperation. Therefore, this study aims at sensorless bilateral control using Hall ICs. A proposed bilateral control does not necessarily require disturbance observers unlike a conventional method originally using high-resolution sensors. Owing to this advantage, low-resolution sensors are applicable to the proposed bilateral control. Experiments showed that the proposed method succeeded bilateral control using Hall ICs without mechanical sensors, although the conventional control did not work using the low-resolution sensors. Therefore, the proposed method will be able to enhance fault-tolerance of teleoperation systems.

© 2019 IEEE. This paper proposes an operational force reduction method for four-channel bilateral teleoperation under time delay. The four-channel bilateral control is an attractive way to realize a remote control with haptic sensation. In general, the haptic sensation deteriorates under the time delay in the four-channel bilateral teleoperation, e.g., operationality of the teleoperation, stability of the system, and other performances. To improve the operationality in free motion, a communication disturbance observer and a three-channel bilateral control have been proposed. Although the operational force in the free motion is reduced by these methods, the system becomes asymmetric. This means that the performance of the remote control from the slave side deteriorates in these methods. To overcome this problem, a novel symmetric compensator by using variable compliance control is proposed. A feedback gain is varied based on a power flow direction. The validity of the proposed method is confirmed by experimental results.