論文

© 1973-2012 IEEE. In a demonstration (DEMO) reactor, mitigation of the large heat load on the divertor target to the below material and engineering limits is a key requirement for operation. Systems modeling is used to design entire fusion power plants and, therefore, has to be able to appropriately capture the divertor challenge. Therefore, it is important to validate these models against comprehensive SOL-divertor simulation codes and experiments. A 1-D divertor model in PROCESS was investigated, compared to the results of 2-D SONIC simulation under the detachment condition. The comparison shows how the 1-D divertor model handles the power loss mechanisms from the outboard mid-plane to the outer divertor target for a DEMO-like condition. The results show good agreement on the calculated value of the total power crossing the separatrix (<5% difference) and the total impurity radiation power P imp (<10% difference). However, the 1-D profiles show differences in density and temperature at the upstream of the target (<10 m of connection length to target, corresponding to 10 cm in the poloidal length). One reason for this difference is that the 2-D model calculates impurity transport, which produces a variable impurity fraction along the connection length in the divertor, while the 1-D model uses a single averaged value. The SONIC code also considers physical processes not covered in the 1-D model, such as radial transport in the SOL and divertor region. A scan of P sep values in PROCESS for a DEMO-sized machine show that above Psep = 200 MW, there is a stronger impact on cost and machine size for higher Psep.

© 2020 Author(s). To increase the accuracy of a particle, momentum, and energy source terms in the detached helium plasma simulation, rate coefficients with the collisional-radiative model were introduced into the fluid code LINear Divertor Analysis (LINDA). Obtained effective rate coefficients and related source terms were compared with those from the conventional empirical databases. It is shown that a high-density condition in future fusion devices causes larger deviation between the effective and the empirical source terms. One-dimensional detached plasma simulation indicated that the peak amplitude of the plasma density during the rollover is sensitive to the source term difference related to the recombination. This study additionally revealed that the heating effect in the three-body recombination process strongly affects the detached plasma formation and downstream plasma parameters.

The transition phenomenon of detached plasma during additional heating effects has been studied by applying a short pulse (25 ms) of Electron Cyclotron Heating (ECH) at the east plug-cell of the tandem mirror device GAMMA 10/PDX. In this paper, the plasma parameters on the target plate of the D-module are studied for understanding the impact of transient heating pulse on the sustainability of the detached plasma. The heat flux increases on the target plate for the additional heating case in comparison to without heating pulse. The ion flux also increases when the ECH heating is activated. The electron density enhances significantly during the ECH heating pulse application period. Furthermore, the electron density and the ion flux increase according to the increment of Xe plenum pressure in the case of ECH heating condition. The experimental results clarified that ECH heating pulse can drive the detachment state to attached state in spite of strong effect of Xe gas for generating the detached plasma.

Eulerian–Lagrangian (EL–LG) scheme is a numerical scheme that tracks pseudo particles in Eulerian cells. It is widely used in the computational fluid dynamics, however, numerical errors associated with a particle source term has not yet been investigated much. Hence this study focuses on numerical errors of EL–LG caused by particle sources. The purposes are: (i) to clarify causes and situations that bring larger numerical errors by source terms and (ii) to suggest an idea to reduce them. For those purposes, we focus on the particle continuity equation and carry out systematic analysis of the numerical error by setting the following three simple cases: Case (A) No source, Case (B) Constant source, and Case (C) source with arbitrary spatial profile. For each case, we have obtained a theoretical expression of the numerical error. It has been clarified that the errors become relatively large when (i) the spatial profile of the particle source has a large gradient and (ii) the source is localized in the region with high flow-velocity. These were caused by the treatment of the particle source: If pseudo particles due to the source are added in a simple way at the start or the end of the time step, this can lead to larger numerical errors. To reduce those errors, a time-averaging scheme has been suggested. Although the analyzed cases are simple, the results obtained in this study would give important knowledge and insight into numerical errors associated with particle sources in EL–LG schemes.

Concepts of the power exhaust and divertor design have been developed, with a high priority in the pre-conceptual design phase of the Japan-Europe broader approach DEMO design activity (BA DDA). Common critical issues are the large power exhaust and its fraction in the main plasma and divertor by the radiative cooling (P radtot/P heat 0.8). Different exhaust concepts in the main plasma and divertor have been developed for Japanese (JA) and European (EU) DEMOs. JA proposed a conventional closed divertor geometry to challenge large P sep/R p handling of 30-35 MW m-1 in order to maintain the radiation fraction in the main plasma at the ITER-level (f radmain = P radmain/P heat ∼ 0.4) and higher plasma performance. EU challenged both increasing f radmain to ∼0.65 and handling the ITER-level P sep/R p in the open divertor geometry. Power exhaust simulations have been performed by SONIC (JA) and SOLPS5.1 (EU) with corresponding P sep = 250-300 MW and 150-200 MW, respectively. Both results showed that large divertor radiation fraction (P raddiv/P sep 0.8) was required to reduce both peak q target (10 MW m-2) and T e,idiv. In addition, the JA divertor performance with EU-reference P sep of 150 MW showed benefit of the closed geometry to reduce the peak q target and T e,idiv near the separatrix, and to produce the partial detachment. Integrated designs of the water cooled divertor target, cassette and coolant pipe routing have been developed in both EU and JA, based on the tungsten (W) monoblock concept with Cu-alloy pipe. For year-long operation, DEMO-specific risks such as radiation embrittlement of Cu-interlayers and Cu-alloy cooling pipe were recognized, and both foresee higher water temperature (130 °C-200 °C) compared to that for ITER. At the same time, several improved technologies of high heat flux components have been developed in EU, and different heat sink design, i.e. Cu-alloy cooling pipes for targets and RAFM steel ones for the baffle, dome and cassette, was proposed in JA. The two approaches provide important case-studies of the DEMO divertor, and will significantly contribute to both DEMO designs.

An integrated divertor simulation code, SONIC, An integrated divertor simulation code, SONIC, has been developed in order to predict a self-consistent transport solution of the plasma, neutral and impurities in the scrape-off layer (SOL) and divertor. SONIC code has contributed to determining the divertor design and power handling scenarios for the Japanese (JA) fusion demonstration (DEMO) reactor. Radiative cooling scenario of Ar impurity seeding and the divertor performance have been demonstrated to evaluate the power exhaust scenarios with . The simulation identified the decay length of the total parallel heat flux profile as being broader than the electron one, because of the ion convective transport from the outer divertor to the upstream SOL, produced by the plasma flow reversal. The flow reversal also reduced the impurity retention in the outer divertor, which may produce the partial detachment. Divertor operation margin of key power exhaust parameters to satisfy the peak was determined in the low of under severe conditions such as reducing radiation loss fraction, i.e., and diffusion coefficients and . The divertor geometry and reference parameters rad) were consistent with the low operation of the JA DEMO concepts. For either severe assumption of or and to their half values, higher operation was required. In addition, recent investigations of physics models (temperature-gradient force on impurity, photon transport, neutral-neutral collision) under the DEMO relevant SOL and divertor condition are presented.

A large superconducting machine, JT-60SA has been constructed to provide major contributions to the ITER program and DEMO design. For the success of the ITER project and fusion reactor, understanding and development of plasma controllability in ITER and DEMO relevant higher beta regimes are essential. JT-60SA has focused the program on the plasma controllability for scenario development and risk mitigation in ITER as well as on investigating DEMO relevant regimes. This paper summarizes the high research priorities and strategy for the JT-60SA project. Recent works on simulation studies to prepare the plasma physics and control experiments are presented, such as plasma breakdown and equilibrium controls, hybrid and steady-state scenario development, and risk mitigation techniques. Contributions of JT-60SA to ITER and DEMO have been clarified through those studies.

In divertor plasmas, atomic processes play a significant role in reducing the divertor heat load. In particular, the elastic scattering between ions and neutral particles can be characterized as a large-angle scattering; this is in contrast with Coulomb scattering, which is dominated by small-angle scattering. In a large-angle scattering, a large fraction of the ion energy is transferred to the neutral particle, and the particle flight direction can be changed significantly. This process can generate additional particle transport perpendicular to magnetic field lines and affect plasma density profile in neutral-rich divertor regions. However, in most edge plasma simulation codes, the elastic scattering with neutral particles is not taken into account in the direction perpendicular to the magnetic field lines. In this study, we performed a 2D orbital calculation without other drifts such as diamagnetic and E × B drifts to assess the effect of the elastic scattering on the density profile. The peak density is found to be decreased by 11.1 (6.3)% compared with the model that ignores the transport due to the elastic scattering, even at 3.0 (5.0) T magnetic field similar to that of the JT-60SA (JA DEMO reactor) class. In addition, the ion transport can be expressed as a diffusion model by integrating the differential cross section over the large-angle scattering range (Formula presented.). The proposed method may be easily introduced into any integrated codes to consider the elastic scattering.

Quantum computing can be used to speed up the simulation time (more precisely, the number of queries of the algorithm) for physical systems; one such promising approach is the Hamiltonian simulation (HS) algorithm. Recently, it was proven that the quantum singular-value transformation (QSVT) achieves the minimum simulation time for HS. An important subroutine of the QSVT-based HS algorithm is the amplitude amplification operation, which can be realized via the oblivious amplitude amplification or the fixed-point amplitude amplification in the QSVT framework. In this work we execute a detailed analysis of the error and number of queries of the QSVT-based HS and show that the oblivious method is better than the fixed-point one in the sense of simulation time. Based on this finding, we apply the QSVT-based HS to the one-dimensional linearized Vlasov-Poisson equation and demonstrate that the linear Landau damping can be successfully simulated.